Nicolas Marriott

[Nicolas Marriott @NicolasMarriott]

@RobShaw_BC I can relate with that excuse tbh.

[Nicolas Marriott @NicolasMarriott]

@RobShaw_BC 0 stars. Host has a shower cam.

[Elon Musk @elonmusk]

This is the future we shall bring into being

[Nicolas Marriott @NicolasMarriott]

@RobShaw_BC Hmm I have ideas.

[Nicolas Marriott @NicolasMarriott]

@VaughnPalmer They used phantom math to mask a surging deficit and dodge an immediate credit rating downgrade. Simple as that.

[Nicolas Marriott @NicolasMarriott]

@TunezUS @jakeufps It has a dual core mcu and better circuit design than other mice.

[Nicolas Marriott @NicolasMarriott]

@Lamzugear I can do some testing.

[Nicolas Marriott @NicolasMarriott]

@CaIypto Using Presentmon I found frametiming was much more consistent using rtss than the engine from my earlier testing.

[Nicolas Marriott @NicolasMarriott]

@AimAdapt @Lamzugear Uping the polling rate passed 4k is not the path to be ahead of the curve. There are more important improvements that can be made to the technology that have a bigger impact imo. Better wireless technology, dual core mcu, emi and interference mitigation, etc.

[Nicolas Marriott @NicolasMarriott]

@TenZOfficial @ProdigyAgencyGG Push for a dual core mcu. It makes a big difference.

[Nicolas Marriott @NicolasMarriott]

@ArraJx @dizzy Can happen due to electricity or a wiring issues in his house. Neutral line voltage and/or ground fault causing interference, low frequency noise which will damage a computer over time or quickly depending on the severity.

[Nicolas Marriott @NicolasMarriott]

@Lamzugear Appreciate you guys looking into the issue immediately and trying to find a solution as fast as you can and also listening to anyone with an issue and reaching out to me. Great company and a fantastic product! Keep it up! 👍

[Nicolas Marriott @NicolasMarriott]

@jordanbpeterson Thought it was Fidel Castro for a sec.

[Nicolas Marriott @NicolasMarriott]

@xTheWhale_ Raising DPI up to 6400+ and lowering you polling rate to 500hz, then use rawaccel to lower sensitivity multiplier to 0.25 or so. It's the most responsive mouse feel. Allows the sensor to pretty much always run at 500hz even on very slow mouse movements. Feels better than 8k hz.

[Nicolas Marriott @NicolasMarriott]

@elonmusk @elonmusk I edited that side window. Might be just me but I think that subtle change looks a lot better. 🤔

[Nicolas Marriott @NicolasMarriott]

@Joseph248Canada @The_Bread_Bros @clownworld Helping regardless of the potential of being sued (which wouldn't happen) is part of being a "hero". Getting sued shouldn't be on the top of the list of concerns for helping a man in a situation like that anyways. You should be more concerned about getting stabbed yourself.

[Nicolas Marriott @NicolasMarriott]

@stormentv Take a quick check with Latencymon to see if it's high DPC latency and which driver is causing it. It's free software.

[Nicolas Marriott @NicolasMarriott]

@stormentv I'm willing to bet it's interrupts caused by Nvidia drivers causing high DPC latency Set the interrupt affinity for your GPU to a single core using Interrupt Affinity Policy Tool and make sure to enable MSI mode on your 4090.

[Nicolas Marriott @NicolasMarriott]

@StvUnkzz @Lamzugear You can't because it wont work. The og v2 uses a different pcb with a compx mcu. This new 4k version using a nordic mcu.

[Nicolas Marriott @NicolasMarriott]

@Lamzugear @Berghzy1999 Here's another mistake if you want to fix that one too haha.