Caleb Morgan

[Caleb Morgan @CalebMorgan120]

This is a prototype prosthetic arm that I printed and assembled for a student here @SabinePassISD @t3chl0gic @HagedornScott #prosthetic #3Dprinting

[Caleb Morgan @CalebMorgan120]

I used @DupliColor spray paint and a mixture of @HATCHBOX3D @FiberForceItaly PLA filaments

[Caleb Morgan @CalebMorgan120]

The is the Iron Man helmet that I have been working. It is #3dprinted and painted and has LED strips under the eyes. @HagedornScott @t3chl0gic @Marvel @RobertDowneyJr @Ultimaker #Marvel #superhero #ironman

[Caleb Morgan @CalebMorgan120]

@HagedornScott @SabinePassISD

[Caleb Morgan @CalebMorgan120]

This is the fan stand that I printed out of Tough Black PLA and was very pleased to see that it still oscillates. @HagedornScott @t3chl0gic @Ultimaker #3Dprinting @AutodeskEDU

[Caleb Morgan @CalebMorgan120]

These rings are printed from the Tough Black @Ultimaker PLA. I decided to do a strength test by doing pull-ups on them. They are 4mm thick and I weigh about 130 lbs and they bended slightly but overall held together perfectly. @HagedornScott @t3chl0gic #3Dprinting

[Caleb Morgan @CalebMorgan120]

This is a stand for an oscillating fan that I have printed on an Ultimaker S5. It is made from tough black PLA and it is very structurally sound. @HagedornScott @t3chl0gic @Ultimaker @AutodeskEDU #3dprinting

[Caleb Morgan @CalebMorgan120]

@HagedornScott

[Caleb Morgan @CalebMorgan120]

My first prototype shoe was made to fit a child and it overall seemed to fit how it should. The middle might just be a bit too tight and need some adjusting. @HagedornScott @t3chl0gic @NinjaTek3D @AutodeskEDU @Creality3D #3dprinting

[Caleb Morgan @CalebMorgan120]

Here is a small version of my 3D Printed shoe made with @NinjaTek3D flexible filament. @Creality3D @HagedornScott @t3chl0gic @VANS_66 @Converse #3Dprinting @AutodeskEDU

[Caleb Morgan @CalebMorgan120]

Here is a small lampshade that I made. I could not use a lamp in my house but my ceiling fan works just fine @HagedornScott @t3chl0gic @AutodeskEDU @Ultimaker #3Dprinting

[Caleb Morgan @CalebMorgan120]

Here is a video of my small boat. It floated and managed to hold another small prototype boat. I've made some adjustments for the larger one in hopes that it will be able to hold and distribute weight more easily. @t3chl0gic @HagedornScott @AutodeskEDU @DremelDigiLab #3Dprinting

[Caleb Morgan @CalebMorgan120]

For our movie/TV prop I wanted to make the Sling Ring from Dr. Strange in the #Marvel movies. @HagedornScott @t3chl0gic @SabinePassISD @Ultimaker @AutodeskEDU #3Dprinting

[Caleb Morgan @CalebMorgan120]

Made my spinning object. @HagedornScott @t3chl0gic @SabinePassISD @Creality3D @formlabs @AutodeskEDU #3Dprinting

[Caleb Morgan @CalebMorgan120]

My first 3D printed pen. Sadly it broke so I had to superglue the middle. The next one will have thicker walls. @HagedornScott @t3chl0gic @SabinePassISD @formlabs @AutodeskEDU #3Dprinting

[Caleb Morgan @CalebMorgan120]

Made my special cube. @HagedornScott @t3chl0gic @SabinePassISD @formlabs @AutodeskEDU #3Dprinting

[Caleb Morgan @CalebMorgan120]

@HagedornScott @SabinePassISD Cheese Cake all the way

[Caleb Morgan @CalebMorgan120]

Made my first cube. @HagedornScott @t3chl0gic @SabinePassISD @Creality3D @AutodeskEDU #3Dprinting