Detail Custom Toys

Graduate of the Art Institute, completed 20 years of military service and a life long collector of 80's pop culture (GI JOE, STAR WARS, MASK, ect.)

[Detail Custom Toys @DetailCustomToy]

I had a request so here is the link to my Cobra IMP .50 Cal machine gun. @HISSTANK #GIJOE @3DJoes
https://t.co/J68Z8cU2U3

[Detail Custom Toys @DetailCustomToy]

Other side of the long box. Nice to get back into airbrushing a bit. #GIJoe #LongBox

[Detail Custom Toys @DetailCustomToy]

It has become extremely rare that I airbrush, so when the long box that I keep my GI JOE comics in needed to be replaced after 30 years and a dozen or so moves, I decided to use the opportunity to practice. The box didn't turn out perfect, but it is not awful. #GIJoe #LongBox

[Detail Custom Toys @DetailCustomToy]

Cobra IMP BIO missile print turned out OK. The BIO canisters work with the latch so I think that it is ready to paint. #Cobra #IMP @HISSTANK #GIJoe

[Detail Custom Toys @DetailCustomToy]

Just about ready to assemble the Pip-Boy for my son's birthday. @anycubic3dprint #Fallout #pipboy

[Detail Custom Toys @DetailCustomToy]

@Shawnforward13 @JoeBattlelines Lets not get crazy.

[Detail Custom Toys @DetailCustomToy]

I'm finally getting around to printing my COBRA IMP BIO-Missle. This is going to take 15 hours on my 3D printer. I hope the supports work out. #GIJoe #Cobra #IMP @HISSTANK @ANYCUBIC_3D @tinkercad

[Detail Custom Toys @DetailCustomToy]

Now that I have clear resin again, I busted out a test print of my IMP Blast Shield. I can see where I need to make improvements and how I want to make room for the .50 cal. #IMP #Cobra @HISSTANK #GIJoe @ANYCUBIC_3D @tinkercad

[Detail Custom Toys @DetailCustomToy]

Almost done. I'm going to print some lens caps for the scope. Otherwise, not bad. #DL44

[Detail Custom Toys @DetailCustomToy]

So many projects..... so little time. Gonna finish up Han's DL-44 blaster. It's just a quick easy paint job, then I need to finish the Pip-Boy I'm making for my son's birthday.

[Detail Custom Toys @DetailCustomToy]

How many projects are too many? I'm customizing a Han Solo DL-44 costume blaster that was too cheap and easy to pass up, the Desert HISS, and 3D printing a Pip-Boy for my son's birthday. And the minifigs..... sooo many minifigs.

[Detail Custom Toys @DetailCustomToy]

Digital desert camo waterslide decals are working out. They are a bit sensitive but there have been no failures so far. #HISS

[Detail Custom Toys @DetailCustomToy]

Primed and ready for decals. #HISS

[Detail Custom Toys @DetailCustomToy]

My new coffee mug.

[Detail Custom Toys @DetailCustomToy]

Test print for the HISS Autocannon. Not bad. @HISSTANK @GeneralsJoes #GIJOE #HISS

[Detail Custom Toys @DetailCustomToy]

This week I'm working on an Autocannon for a custom Desert HISS. @HISSTANK #GIJOE #HISS

[Detail Custom Toys @DetailCustomToy]

After much tweaking, the Cobra HISS gun bracket replacement part is done. The link to the file on Thingiverse is below. @HISSTANK #GIJoe #HISS @tinkercad @anycubic3dprint https://t.co/fe6jh9Nj0m

[Detail Custom Toys @DetailCustomToy]

Coole beans.

[Detail Custom Toys @DetailCustomToy]

The test print is done. Needs just a tiny bit of tweaking. @GeneralsJoes @HISSTANK #GIJoe #HISS @anycubic3dprint

[Detail Custom Toys @DetailCustomToy]

Working on my HISS Tank mod. Needed a replacement mounting bracket for the gun. I'll throw it on the Photon and if it works I'll put the file up on Thingiverse. @GeneralsJoes @HISSTANK #HISS @anycubic3dprint