Johnny Mack Customs

Passionate about bringing old cars and antique trucks back to life! Restorations, Repairs, Upgrades and Custom Metal work

[Johnny Mack Customs @JohnnyM11194138]

@FFT1776 Darth Vader’s mom… 🙄😂😂

[Johnny Mack Customs @JohnnyM11194138]

@JeffMG68 Very cool! I had a blue short bed ‘79 4x4 while in college.

[Johnny Mack Customs @JohnnyM11194138]

Working on a 1949 Ford truck for a customer, lots of rust repair, body work, extra HP and more modern interior.

[Johnny Mack Customs @JohnnyM11194138]

1951 Chevy wagon, we pulled the old straight 6 and installed a 340hp small block with an overdrive transmission, added a/c, power disc brakes and a little chrome to dress up the engine bay.

[Johnny Mack Customs @JohnnyM11194138]

1956 Chevy 2 door post in for a new drivetrain, the 235 straight 6 is worn out. Then we’ll install a new American Autowire wire harness as well.

[Johnny Mack Customs @JohnnyM11194138]

@ccgarrett Get out, eat more pork

[Johnny Mack Customs @JohnnyM11194138]

@ilovenostalgia Done ‘em all! 😃

[Johnny Mack Customs @JohnnyM11194138]

@bosalem64546044 Bottom

[Johnny Mack Customs @JohnnyM11194138]

We Do Classic Cars Right at #JonnyMackCustoms!

[Johnny Mack Customs @JohnnyM11194138]

Giving commands to the @bluedemonweld voice-activated, auto darkening welder helmet. #bluedemonweldingproducts
#bluedemon
#johnnymackcustoms

[Johnny Mack Customs @JohnnyM11194138]

My voice-controlled auto darkening welder helmet by @bluedemonweld does the job! #JohnnyMackCustoms

[Johnny Mack Customs @JohnnyM11194138]

A rust repair project on a ‘59 Chevrolet Apache fender and both headlight buckets. #johnnymackcustoms

[Johnny Mack Customs @JohnnyM11194138]

My voice-controlled auto darkening welding helmet from @bluedemonweld! Not my most expensive helmet but definitely my coolest! Love it! #bluedemon #weld #welder #johnnymackcustoms

[Johnny Mack Customs @JohnnyM11194138]

I visited the machine shop to see how the 302 for the '64 Comet is coming along. it's been bored and decked, it has new cam and crank bearings and the cam and crank are installed. Now its getting setup for the roller cam so the customer won't have to use high Zinc content oil.

[Johnny Mack Customs @JohnnyM11194138]

1954 Chevy truck in for new door latches, strikers, door latch relay, vent glass and door glass. https://t.co/JegmKPWfck

[Johnny Mack Customs @JohnnyM11194138]

Visit https://t.co/JegmKPWfck

[Johnny Mack Customs @JohnnyM11194138]

Visit https://t.co/JegmKPWfck

[Johnny Mack Customs @JohnnyM11194138]

Continuing repairs on a customer’s ‘55 Chevy. The aftermarket taillights didn’t fit the aftermarket quarter panels. And a patch panel in the trunk and the last 10 inches and rear body panel getting replaced. #chevy #restoration #hotrod #repair #trifive #tri5 #johnnymackcustoms

[Johnny Mack Customs @JohnnyM11194138]

Painted this old Ford bed for a customer awhile back, finally got a pic with it on the truck!! #sata #3m #ppg #oldfordtruck #hotrod not too bad for a garage paint job!
#johnnymackcustoms

[Johnny Mack Customs @JohnnyM11194138]

Did a little rust repair on a ‘37 Ford pickup fender #johnnymackcustoms