Makis SV1AFN,

[Makis SV1AFN, @MakisSV1AFN]

@tt12514 Σας παρακολουθώ με ενδιαφέρον! Μαθαίνουμε συνεχώς...

[Makis SV1AFN, @MakisSV1AFN]

@SonyMarcony +19 dBm no damage

[Makis SV1AFN, @MakisSV1AFN]

With a 1 mH choke it works from 60 KHZ to more than 1.8 GHZ. With a smaller inductance works up to 2.7 GHZ! More than 17 dB gain, 1 W power output! Highly linear! No harmonics...We need to test more...I will report soon.

[Makis SV1AFN, @MakisSV1AFN]

@willgettoit Well, we are prototyping a new version. The old one was so expensive to make. To be released by the next year...

[Makis SV1AFN, @MakisSV1AFN]

NEW! RG-405 pigtails with SMA plugs, better and more durable than cheap RG-316...even for everyday lab use. Not much more expensive!
https://t.co/ItNFA0jaoU

[Makis SV1AFN, @MakisSV1AFN]

Just released: EMI/FRI Filter for the radio-shack - with a better photo: https://t.co/4SruXWNv68

[Makis SV1AFN, @MakisSV1AFN]

Just released: EMI/FRI Filter for the Radio-room:
https://t.co/4SruXWNv68

[Makis SV1AFN, @MakisSV1AFN]

@RFAmirhosein Yes, this is correct if you use this filter between an antenna and a receiver. But if placed after a multicoupler or LNA then the noise figure is not affected.

[Makis SV1AFN, @MakisSV1AFN]

Air-Band Band-Pass filter to completely eliminate signals from FM broadcasters and the 2-m band
https://t.co/4zTpgojfpg

[Makis SV1AFN, @MakisSV1AFN]

@olegkutkov Stay strong and free!

[Makis SV1AFN, @MakisSV1AFN]

4:1 RF switch DC - 150 MHZ

https://t.co/NLYQW2tDIR

[Makis SV1AFN, @MakisSV1AFN]

NEW: QRO 6-m band-pass filter
https://t.co/4FTwhJF9Ca

[Makis SV1AFN, @MakisSV1AFN]

https://t.co/6j6dQyIm0k

[Makis SV1AFN, @MakisSV1AFN]

https://t.co/BeXCFnETMa

[Makis SV1AFN, @MakisSV1AFN]

https://t.co/rp29fIoeN2

[Makis SV1AFN, @MakisSV1AFN]

@TitanTronics @uhf_satcom It has a 12-ch resistive splitter at the output

[Makis SV1AFN, @MakisSV1AFN]

Coming soon! 12-ch active and filtered antenna splitter for timing applications

[Makis SV1AFN, @MakisSV1AFN]

@Jdling2 Hehe! It reminds you anything similar? it looks like a DF but it is just a resistive splitter

[Makis SV1AFN, @MakisSV1AFN]

@yashiro_ld I am making a new one with non-magnetic components, when I finish I will send you one to try!

[Makis SV1AFN, @MakisSV1AFN]

https://t.co/dtm6X95DDW