Mark Pellerin

[Mark Pellerin @MarkPellerin73]

@BDuchek I ran them on fd 140s, they are well worth the money. I never had much issue with them riding over. Only remember breaking one, they are durable.

[Mark Pellerin @MarkPellerin73]

@embdenhaymaker Do you have a spinner knob on your steering wheel? R4045 would do the same thing, my dad finally figured out the weight of it when it was shaking would move the wheel just enough if it was on the side or on top to disengage

[Mark Pellerin @MarkPellerin73]

@ChristiFriesen We have one in our shop, it will be put in the service truck during busy seasons. We try to keep the crew updated on first aid as well

[Mark Pellerin @MarkPellerin73]

@BantrySeedFarms I think Triple Threat Diesel in Grande Prairie has a couple and a DD16

[Mark Pellerin @MarkPellerin73]

@landon707

[Mark Pellerin @MarkPellerin73]

@ChuckWeinknecht @stinkynutss I don’t see that with my 8800/45’. In decent crops always power is limiting factor. I adjust loss sensors to actual losses and Cemos adjusts accordingly. Can’t comment on the x9 though, haven’t seen a demo

[Mark Pellerin @MarkPellerin73]

@BenoitFamFarm @TELUS Same here. Old phone did it, new phone is almost worse

[Mark Pellerin @MarkPellerin73]

@Denny2point0 @ChDpVentures could probably fix it?

[Mark Pellerin @MarkPellerin73]

@willmuller3 I have belts, run them a little tighter than the book says. If you jump one you should loosen all the slat bolts off, rotate a few times then tighten them back up to get all lined up. I’d take belts any day, I feel they can handle rocks better

[Mark Pellerin @MarkPellerin73]

@ShawnJacula I’ve used one for a couple years, wouldn’t be without it now. It saves a lot of steps

[Mark Pellerin @MarkPellerin73]

@BDuchek Mines got a pile of acres on it, never any downtime. The square edges on the carbide are nice with full down pressure, they can move some dirt around. Rolling hills it contours fairly well. When mines due for upgrade I’ll buy the same thing again

[Mark Pellerin @MarkPellerin73]

@T_Bartman @deep_seeder Pea auger parts, center canvas drive motor and roller were hard to come by, several other small things. Also my dealer was limited on FD2s they could order

[Mark Pellerin @MarkPellerin73]

@T_Bartman @deep_seeder Poor MD parts availability this past fall was one of the main reasons for switching. Lots of in cab adjustments is nice, I think MD would contour better in rolling hills and draws, but we’re fairly flat so not a big concern for me. I didn’t try an FD2

[Mark Pellerin @MarkPellerin73]

@T_Bartman @deep_seeder I demoed a 40’ Convio last fall, currently use fd140’s. Tall green green canola, the Convio was very impressive. Far better feeding tall bushy canola than the MD. Ended up trading to Convio’s

[Mark Pellerin @MarkPellerin73]

@BDuchek Second year with Agtron Legend and it’s been flawless so far. I’m really happy with it

[Mark Pellerin @MarkPellerin73]

@RonKrahn I know a few of the colonies around GP if you want to message me

[Mark Pellerin @MarkPellerin73]

@Plantmore1 @JasonWiwadBP @HockeyCanada We have one in the HSL as well and the development we’re seeing is unreal

[Mark Pellerin @MarkPellerin73]

@BantrySeedman I’m not far from there, I’ve never heard anything bad about them. If there’s something your looking at I could stop by there tomorrow

[Mark Pellerin @MarkPellerin73]

@58thF DeBolt, between GP and VV