PartyLime

[PartyLime @PartyLimeOG]

@Barnacules Jaguar D type any day

[PartyLime @PartyLimeOG]

@C0677764813281 @BASF Unfortunately, the filament has been discontinued. Kimya make one though https://t.co/zg1uLj3WNg

[PartyLime @PartyLimeOG]

Finally found a good material for this @BASF TPC printed on the P1S #AirlessBasketball #3dprint

[PartyLime @PartyLimeOG]

@loyalmoses I like the Adam Savage rule. Buy the cheapest. When it breaks, buy the most expensive. Means you only buy nice tools when you use them enough to warrant it

[PartyLime @PartyLimeOG]

@Prusa3D @josefprusa why can't I use my printables vouchers on one order? I don't want to pay shipping 3 times over. I saved them up so I can order some merchandise with some filament at the same time and not pay shipping 3 times. It's £15 a delivery to the UK!

[PartyLime @PartyLimeOG]

@joeltelling @That1NetworkGuy @Barnacules If you want it to bounce I'd recommend TPC instead of TPU. It's hard to get hold of bit it makes for a very bouncy durable ball. The other one I've seen that looks like it works is PEBA.

[E3D @E3DOnline]

🥳🚨 GIVEAWAY TIME! To be in with the chances of winning a pair (0.4mm & 0.6mm) of High Flow ObXidian @BambulabGlobal Hotends all you need to do is make sure you're following E3D, retweet this post and tag your mates in the comments!

Winner revealed Friday 17th May @ 18:00 GMT👀

[PartyLime @PartyLimeOG]

@E3DOnline @BambulabGlobal @Benwfowler

[PartyLime @PartyLimeOG]

@jabrils_ @repkord @Prusa3D @printablescom This one bounces well :)

[PartyLime @PartyLimeOG]

@Chirpy277 @3DPrintGeneral Out of interest, what do you mean by fixed?

[PartyLime @PartyLimeOG]

@Krommsan @BambulabGlobal I printed one in BASF TPC. It bounces really well and feels super durable

[PartyLime @PartyLimeOG]

@jkonman @BambulabGlobal @PiNK_3DP I beg to differ! I think the original is some kind of TPC blend. This is mine printed in TPC

[PartyLime @PartyLimeOG]

@meatloaf2002 @BambulabGlobal Check the link in my bio. Printed in TPC and it bounces great 👍

[PartyLime @PartyLimeOG]

@SimianGuy @BambulabGlobal Printed on the P1S 👍

[PartyLime @PartyLimeOG]

@FerTech @BambulabGlobal TPC works a treat!

[PartyLime @PartyLimeOG]

@BASF @3DPrintGeneral @UncleJessy4Real @3dprintingnerd @joemag3D check it out. It's a good bounce and seems to be lasting well

[PartyLime @PartyLimeOG]

@BASF @3DPrintGeneral @UncleJessy4Real @3dprintingnerd It's not quite a full bounce but it's about 90% there

[PartyLime @PartyLimeOG]

@3DPrintGeneral Looks like the extruder printing the white material re-homes itself after a few layers of being off. Seems like strange behaviour to me. Have you tried loading the code into prusaslicer gcode viewer to check its not a slicer issue?