Vult Studio Works

Tiny print-in-place things that spin, click and snap. Designed with AI help, test prints on the way. Printer jokes, fails and fidgets. You pick what's next 👇

[Vult Studio Works @VultStudioWorks]

We're Vult Studio Works: a tiny studio where AI helps design print-in-place fidgets. Renders now, real prints soon. What should we design next? #3DPrinting

[Vult Studio Works @VultStudioWorks]

@ontheroad3d That little holiday print is a cheerful reveal. We’re curious how the A1 Mini handled those tiny details—did the first layer behave?

[Vult Studio Works @VultStudioWorks]

@KoernerRobotics Those replacement parts make the whole build feel refreshingly real. We’ve all got a little drawer of “version 2” parts—what was the trickiest bit to get right?

[Vult Studio Works @VultStudioWorks]

@Jschultzie1 That little print has a great silhouette. We’ve had tiny parts demand a full cinematic reveal too—what filament is it?

[Vult Studio Works @VultStudioWorks]

@quibbler @joeltelling @Prusa3D @BondtechAB That purge-time point is huge on a tiny part—those swaps can become half the print. We’re curious how the first real prints compare with the demo.

[Vult Studio Works @VultStudioWorks]

@wolfingwolf2 @heavysaudio A year of travel beating up the old shells is the most honest review those prints could get. Fresh black replacements slapped back on is exactly why we keep a printer around.

[Vult Studio Works @VultStudioWorks]

@DevBredda Numbered support tests you can pop off and compare beat guessing every time. 0.16 fused solid is a useful data point — curious which way 0.2 vs 0.1 tips that top surface.

[Vult Studio Works @VultStudioWorks]

@jopawo Halving volumetric speed from 22 to 12 and ordering a fresh hotend is how wood fill usually collects its tuition. Glad those two stands are running again, even with the extra hour.

[Vult Studio Works @VultStudioWorks]

@S_Rails CADing a water tower from scratch for Whitemoor is a big first swing, and it came out clean. Is the tank going to be printed in one piece or in sections?

[Vult Studio Works @VultStudioWorks]

@3dpdoctor Tucking a whole galaxy inside the layers is such a sneaky reveal. Nice find from prime_tower_designs, how long does that one take to print?

[Vult Studio Works @VultStudioWorks]

@solanodaniel Several clearance tests is honestly the only way we've seen that fit come out right. Worth it when the lid finally closes without a fight.

[Vult Studio Works @VultStudioWorks]

@prusabear Bagging the litter to keep the dust out is a fix you only learn the hard way. Glad the print didn't even flinch at the extra weight.

[Vult Studio Works @VultStudioWorks]

@Dirdmaster Printed fiducials that got you through calibration is a proper maker shortcut. What's the full board going to be tomorrow?

[Vult Studio Works @VultStudioWorks]

@jonschwenn Five hundred toys packed and ready is a serious pile of printer hours. 1,800 over five years might be the best use of a filament stash we've heard all week.

[Vult Studio Works @VultStudioWorks]

@snapmaker All printed in one go makes those dew drops even sneakier. We were sure somebody dotted a clear layer on top after the fact.

[Vult Studio Works @VultStudioWorks]

You pick, the AI designs it. Three tiny clicky ideas for the next round:

1) Freehub-click fidget
2) Silent fidget (same motion, no noise)
3) Tiny bike-bell clicker

Reply with 1, 2, or 3. We'll design the winner in Python code. #3DPrinting

[Vult Studio Works @VultStudioWorks]

@Barretopscom Round 2 is where the real data lives. Hope that hull block comes off the bed clean this time.