We Have Fun

Two Canadians travelling the world, going on spooky adventures, making unique creative stuff, and having some fun! 🥳

[We Have Fun @_WeHaveFun_]

@LukesLaboratory @YuTR0N You were supposed to machine the bed surface flat. What are those? Speed holes?! 😅

[We Have Fun @_WeHaveFun_]

@BrandonFugal @HISTORY Why not just let Cypress Hill perform near the bubble? 🌱💨

[We Have Fun @_WeHaveFun_]

@LDOMOTORSJASON @LDOmotors Input shaping and accelerometer at the nozzle?! 🤯

[We Have Fun @_WeHaveFun_]

@LukesLaboratory They’ve been very kind about body image, I’ll let it slide.

[We Have Fun @_WeHaveFun_]

@LukesLaboratory Why not machine something to be perfectly flat for cheaper?

[We Have Fun @_WeHaveFun_]

@Anthony_Prusa3D @MandicReally *looks again*

Ohhh, I get it. It’s a thin flat boi that connects or sits on the long bois. Smart! I’m engineering some locking mechanisms for a project, look up some designs to consider incorporating.

Love to see this evolve further! 🥰

[We Have Fun @_WeHaveFun_]

@Anthony_Prusa3D @MandicReally Nicely done! Consider internal ribs / organic designs, and think “how strong can I build this, with minimal filament”.

Engineer strength into those long-bois by inserting metal hardware rods (rebar) that anchors into the wall.

Off to experiment with PPS-GF reinforcement. 🥳

[We Have Fun @_WeHaveFun_]

@tommy_prusa3d @josefprusa @conservancy You are absolutely correct here. I was hoping to save us some time and get right to the source. I respect your position and will respond to the support agent when I have time to work on this. Thanks again. 🥰🙏

[We Have Fun @_WeHaveFun_]

@josefprusa @joescalon

[We Have Fun @_WeHaveFun_]

@BrandonFugal @Akam1129 Impressive. Reduce human latency and operator neck pain. I would opt for a single pane of glass consolidation. 😘

[We Have Fun @_WeHaveFun_]

@schiffer_soft @PRUSA @josefprusa @tommy_prusa3d @PrusaGuy @Prusa3D Does it have a direct dial to customer support? 🥳

[We Have Fun @_WeHaveFun_]

@BrandonFugal @HISTORY 🥳❤️🚀

[We Have Fun @_WeHaveFun_]

@repkord Deeply scarred by Prusa’s MMU2S. 🤭

No fires there, but I did have a bidet electrical fire once, that quite literally scared the shit out of me. True story.
💩🚽

[We Have Fun @_WeHaveFun_]

@DIYMaker_Johan Look into your “consumer protection laws” in your country, and learn all of your actual options and rights.

Hope you’re doing okay. 😘

[We Have Fun @_WeHaveFun_]

@DIYMaker_Johan @Creality3dP @ARTME3D All good man. I understand you.

Just don’t limit yourself. Find your value. Film and post reviews of what you have and why you like or don’t like, establish your value and your audience, then pitch..?

[We Have Fun @_WeHaveFun_]

@DIYMaker_Johan @Creality3dP @ARTME3D Trying to think of options if you can’t afford theirs or get the value you want out of it? No offense taken, this might just be a “hey, I’ll take one of these if you need a tester” calls that I misread?

[We Have Fun @_WeHaveFun_]

@DIYMaker_Johan @Creality3dP @ARTME3D Yep, urgency,. I have a desktop injection moulder with heater bands that likely operates on similar principals.

Break it down, figure it out, figure out how much it would cost to build it, and if it’s worth it. 🤷‍♂️

[We Have Fun @_WeHaveFun_]

@DIYMaker_Johan @Creality3dP @ARTME3D Then it’s a knowledge, materials, tooling, or value/affordability gap.

“I want this, it’s just not for me”
“How much would it cost to get someone to machine some plate steel spinning bois for my shredder?”

Sometimes it’s cheaper than you think.
🥳