Daughter was quicker than the wife. Asked me this afternoon "why are your controllers still in the tree?". Later I found them all on the floor. Then she asked me to help decorate the balls. Mouhahahaha! #christmas#pcengine#retrogaming
Played this for a bit. Current Retro Sprint High Score is 2:22.946. Overall quite nice. 1st thing I did was turn off the modern mode. Really appreciate them adding this as an option. Like the modes and music is ok too. Need to get an original cart now. Will it work on a DMG?
Preparing for a very very NEC Christmas :). Let's see how long this will last until the wife notices and makes me remove it.
#christmas#retrogaming#pcengine
Sold https://t.co/XkxMCoYK86 for #colecovision to a collector in France. He is only missing Choplifter (played this a lot on C64) for a complete collection. So if anyone has a copy you may want to let go, reach out and help this guy complete his Colecovision collection.
PAC was not fully working. LED would not turn on and I never got the on-screen menu. Following @aergon.com's (bsky) advice, cleaned contacts on the back and the legs of the socketed IC with deoxit gold (also reflowed solder points of all ICs). Now LED and on-screen menu are OK.
Tested rgb modded #laseractive with #pcengine PAC and a karaoke LD. My singing sounded awful, must have been bad caps. Karaoke PAC re-cap next project? Should be very do-able. Should I make a cap-map for https://t.co/IqKtkiQmsE wiki or doesn't this count for consoles? #karaoke
@zaxour.bsky.social pointed out the two big purple caps were solid caps and might not be right, so I replaced them with normal electrolytic ones. I didn't even know they were solid. Oops. Everything should be up to specs now. What's next? PAC-N1?
@GarySte20341573 Found it :). Stupid mistake from over a year ago. Never noticed it because I tested with a scart cable with caps and resistors inside.
Picked up my #pcengine Duo again, put it aside after I couldn't get the RGB mod working. Swapped in a #pcengine rgb board meant for the OG PC-Engine coz it has a mini-din socket. Using that I got a (sweet) picture. So the wiring was ok in the end. #retrogaming#retromodding
That was it. Replaced the wrong resistors with still wrong 82 Ohm resistors and I got a better picture. Still very noisy though, but that's probably the make shift scart cable. Will have to order the 75 Ohm resistors, make a proper scart cable and continue later.
I think I might have found the problem. I used 475 Ohm (66A) resistors in-line with the 220uF caps while they should be 75 Ohm. But I don't have any 75 Ohm 0603 smd resistors.... Let's test with 83 Ohm.
@GarySte20341573 I have the caps and resistors on the board, so after making a scart cable without anything in it and setting the jumpers to use them, I get no picture. If I tell it not to use the caps and resistors I get a dim picture missing colours... I need to go back to Scart/RGB 101 class..
@GarySte20341573 Getting very frustrated with this. Pinout of the DIN socket is correct. I was getting a good picture with the saturn cable and mini-DIN directly on the board. But without I can't get a good picture or sometimes a picture at all.
@zaxour Make an adapter, that turns the around slot so you can insert the 32X in like this. Adapter could also add a bit of support on the bottom underneath the 32X.
@MisirajEduart First get things working. Then the next step, will make own scart cable. Actually found double shielded cables locally. About 9eur per meter, DAP MK-832 cable.