L1ng

[L1ng @el1ng0]

@_saagarjha Or even better, they could connect the A13 via PCIe as well and emulate a USB controller like the T2. Or what if the A13 became an external graphics card over PCIe.

[L1ng @el1ng0]

@_saagarjha Same, maybe they resurrected the haywire code and you can push h264 frames to it.

[L1ng @el1ng0]

@_saagarjha I want to know the architecture they're using. Is the A13 just a USB device on an internal hub?

[L1ng @el1ng0]

@s1guza I'm certain they'll offer at least 32GB on the next gen, 64GB if they want to match the current 16". I'm really wondering what their graphics strategy is. Will they still push AMD or do it all in house?

[L1ng @el1ng0]

@nyan_satan I assume so via the right kernel command line, USB pin routing is pretty much direct to the A8 SoC when I traced it out.

[L1ng @el1ng0]

@jamiebishop123 @thejailbreakhub @BendyCatus Was there an issue with the cable I designed? (I'm excited people are doing stuff with the HomePod!)

[L1ng @el1ng0]

@nicolas09F9 @s1guza @winocm @never_released @WhatAintInside @vmlemon The Homepod Mini S4/S5 board is basically that

[L1ng @el1ng0]

@s1guza @devAgamjot Clearly it's x86's fault. I'd be curious to see if any of the M1 UARTs are connected to it (they're not in the DT according to marcan), I see debug looking messages in the firmware like: "link integrity fail"

[L1ng @el1ng0]

@marcan42 @_saagarjha @s1guza I just found the firmware files ... I can't believe it's actually running x86 code

[L1ng @el1ng0]

@marcan42 @_saagarjha @s1guza On the 2900 there's a a UART on the module, I wonder if one of the M1 UARTs is hooked up to it...

[L1ng @el1ng0]

@marcan42 @_saagarjha @s1guza It's a MegaChips MCDP2920 eDP to HDMI converter. Same one is used on the Mac Pro MPX modules. I wonder if using a EDID faker on it would work.

[L1ng @el1ng0]

@s1guza @karetnikovn @svenpeter42 I've had my external monitor only work with one of the ports until I reboot the computer

[L1ng @el1ng0]

@_saagarjha Maybe the accelerometer detects it was moved and causes a recalibration? (e.g. how the Homepod triggers a recalibration). Should be easy for someone to test

[L1ng @el1ng0]

@chronic @gank41 @nyan_satan HomePod remote? 🤔

[L1ng @el1ng0]

@s1guza And then the preinstall script in the pkg contains a nop.

[L1ng @el1ng0]

@DanyL931 @qwertyoruiopz You should do a light up lithophane print

[L1ng @el1ng0]

@DanyL931 Connect your iPhone, iPod touch, iPad or Apple TV to begin.... No Homepod? :-)

Is that the multi-material model or did you change out the filament?

[L1ng @el1ng0]

@RoyLee03753008 First go into DFU, then flip the Homepod back to normal, then start checkra1n and you can jailbreak. If you keep the Homepod upside down it will DFU loop

[L1ng @el1ng0]

Release 1.0 of the HomePod USB+UART breakout boards: https://t.co/A7eIHL0WK6

Check GitHub for more details.

There is very little support around all of this, proceed at your own risk! You will need to fabricate and solder your own PCBs