FLYNQ SnapCap

FLYNQ | SnapCap
The 360° Magnetic Bottle Opener!
🚀 Grab your Late Pledge on Kickstarter

[FLYNQ SnapCap @flynq_snapcap]

400+ backers, $20k+ raised, almost 700% funded on Kickstarter. Every SnapCap is CNC-milled, not cast or stamped, so the edges stay sharp and the fit stays tight. Early Bird rewards still open: https://t.co/bQoocTUHTC

[FLYNQ SnapCap @flynq_snapcap]

We're at 400+ backers and almost 700% funded ($20k+ and counting). The magnet rotates a full 360° so the cap stays put no matter which way you turn the opener. Early Bird rewards are going fast. https://t.co/bQoocTUa44

[FLYNQ SnapCap @flynq_snapcap]

400+ backers in, $20k+ raised, nearly 700% funded. Still time to join and lock in an Early Bird reward. The whole opener is machined from one solid piece of aerospace-grade aluminum - no welds, no joints. https://t.co/bQoocTUa44

[FLYNQ SnapCap @flynq_snapcap]

Thank you to our 400+ backers - we just crossed $20k and almost 700% funded. Each SnapCap gets hard-anodized after machining, so the finish holds up to daily use. Early Bird rewards still available. https://t.co/bQoocTUHTC

[FLYNQ SnapCap @flynq_snapcap]

$20k+ raised, 400+ backers, and climbing toward 700% funded. The 360° magnetic catch holds the cap wherever the opener goes - no more chasing it off the floor. Early Bird rewards are still up. https://t.co/bQoocTUHTC

[FLYNQ SnapCap @flynq_snapcap]

Almost 700% funded and 400+ backers strong. Join them and grab an Early Bird reward before they're gone. Every SnapCap is CNC-machined from a single block of 7075-T6 aerospace aluminum. https://t.co/bQoocTUHTC

[FLYNQ SnapCap @flynq_snapcap]

Did grab your Early Bird discount yet?  Over 400 supporters so far! Our Kickstarter runs until October 9.  https://t.co/bQoocTUHTC

[FLYNQ SnapCap @flynq_snapcap]

#freshlime #sugarcain #clubsoda #giftideas #distillery #bartool #drinking

[FLYNQ SnapCap @flynq_snapcap]

Every SnapCap is machined from a single piece of 7075-T6 aerospace aluminum, then hard-anodized. It's on Kickstarter now. https://t.co/bQoocTUa44

[FLYNQ SnapCap @flynq_snapcap]

#bottleopener #edc #everydaycarry #edcgear

[FLYNQ SnapCap @flynq_snapcap]

Thank you all for your support! We made SnapCap so the cap doesn't end up on the floor. The magnetic catch turns 360° and holds the cap on the opener. Reserve yours for only $39.  See: https://t.co/bQoocTUa44

[FLYNQ SnapCap @flynq_snapcap]

#bottleopener #edc #everydaycarry #edcgear

[FLYNQ SnapCap @flynq_snapcap]

We launched SnapCap on Kickstarter and it was funded in under 10 minutes, and within 24 hours it passed 400% of its goal. Thank you to everyone who backed it and you can still grab an #earlybird https://t.co/bQoocTUa44

[FLYNQ SnapCap @flynq_snapcap]

#Repost the @KamaniGear FLYNQ SnapCap: The 360° Magnetic Bottle Opener https://t.co/qjfbSQEsc2 Overfunded on Kickstarter in 20 minutes, this useful add-on was built to open bottles, lift can tabs, and remove spouts. #bottleopener #edc #everydaycarry #edcgear

[FLYNQ SnapCap @flynq_snapcap]

No mess, no chasing bottle caps across the counter. FLYNQ catches it every time. Early bird discounts go live at launch. [Link in Bio]

#freshlime #sugarcain #clubsoda #giftideas #distillery #bartool #drinking

[FLYNQ SnapCap @flynq_snapcap]

#Repost the Cumeod Drinks Mini Fridge #Competition sponsored by @KamaniGear Enter free https://t.co/xsAFm3NpO9  #winitwednesday #freebiefriday #BeerLovers #CampingGear #OutdoorGear