Top Tweets for #FidgetSpinnerHacks
#fidgetspinnerhacks I updated the code to incrementally delay the strobe. The spinner is actually spinning at 2300 RPMs. Nice strobe baby.
#fidgetspinnerhacks So I added a white LED & hooked it to another arduino output & wrote code to strobe it with the IR sensor signal. Cool
#fidgetspinnerhacks I realigned everything, closed the gap as much as possible and...Yes another Top Speed has been had,118.6Hz or 2372 RPMs
#fidgetspinnerhacks So I was running the Fidgi-motor the other morning and the puck vibrated off, hit the spinner : ( , But no worries.
#fidgetspinnerhacks Added hockey puck on top to shrink air gap between coil & fidget spinner bearings. Another new top speed 2296 RPMs
#FidgetSpinnerHacks Yet another top speed achieved, 110.1Hz or 2202 RPMs! See the whole spin-up video here, https://t.co/LJPgeugpo5
#ImNotAnExpertBut if you're able to hit a hammer between the #fidgetspinner nodes as it spins you'll hear an epic sound #FidgetSpinnerHacks
New video at 8pm on my Facebook page at Sir Stevo Timothy. #fidgetspinner #fidgetever #fidgetspinners #FidgetSpinnerHacks
Saw this picture on Face Book, can't agree more! #FidgetSpinner #business #men #Legacy #BeYou #BringItIn #FidgetSpinnerHacks #staytuned
#fidgetspinnerhacks Getting up to to 92.8 Hz or 1,857 rpm video.
https://t.co/nwb3MvpgpQ
#fidgetspinnerhacks New new top speed achieved. Accomplished by tweaking position and making coil very close to fidget spinner, 1860 rpms!
#fidgetspinnerhacks
New top speed achieved. Accomplished by using a smoother spinning fidget spinner and tweaking position of coil
#FidgetSpinnerHacks #dadHackedmyFidgetSpinner
Check out the coil temperature and the transistor temperature after running for several mins.
#FidgetSpinnerHacks #dadHackedmyFidgetSpinner New coil arrangement, max speed 52.02Hz, 60*(52.02/3)=1040 rpm. Nice!
https://t.co/nwb3MvGROq
#FidgetSpinnerHacks #dadHackedmyFidgetSpinner
Max speed with coil on table was 31.56Hz or 60*(31.56/3) = 631 rpm
#FidgetSpinnerHacks #dadHackedmyFidgetSpinner Output of sensor goes to Arduino just to invert the signal. Arduino out to base of TIP120!
#FidgetSpinnerHacks #dadHackedmyFidgetSpinner e-mag pulsed by darlington transistor TIP125. E18-D80NK sensor used for timing.
#FidgetSpinnerHacks #dadHackedmyFidgetSpinner
The electro-magnet is a twisty deck nail, then put on about 1200 turns of 26awg magnet wire.
Last Seen Hashtags on Sotwe
Trends for you
Most Popular Users
Elon Musk 
@elonmusk
240.8M followers
Barack Obama
@barackobama
119.2M followers
Donald J. Trump
@realdonaldtrump
111.7M followers
Cristiano Ronaldo
@cristiano
111.1M followers
Narendra Modi
@narendramodi
107M followers
Rihanna
@rihanna
97.8M followers
NASA
@nasa
92.2M followers
Justin Bieber
@justinbieber
91M followers
KATY PERRY
@katyperry
87.9M followers
Taylor Swift
@taylorswift13
81.8M followers
Lady Gaga
@ladygaga
73.3M followers
Virat Kohli
@imvkohli
70.3M followers
Kim Kardashian
@kimkardashian
69.9M followers
YouTube
@youtube
68.7M followers
Bill Gates
@billgates
64M followers
Neymar Jr
@neymarjr
63.1M followers
The Ellen Show
@theellenshow
62.4M followers
CNN
@cnn
61.9M followers
Selena Gomez
@selenagomez
61M followers
X
@x
60.8M followers