Hwhipp01

Plant operator and farmhand in corporate agriculture. Broadacre cropping.
Charles study university graduate in Agricultural Business Management 2016

[Hwhipp01 @hwhipp01]

@MattP1Gallagher What was the prediction about no new podium sitters. Most honest deserving rookie to get one. Awesome

[Hwhipp01 @hwhipp01]

I've registered for Oceans to Outback, a month-long challenge to raise vital funds for the Royal Flying Doctor Service and I need your help! Please support me by donating to my fundraising page. https://t.co/kfwq6y0bsq

[Hwhipp01 @hwhipp01]

Just rebuilt several pto clutch units with new pads. What sort of nm of torque should be put on the springs? Will be on chaser bins.
Any advice would be appreciated.

[Hwhipp01 @hwhipp01]

Looking for opinions. Looking at replacing two Kuhn 3pt linkage spreaders. Is Kuhn the way to go or are there better 3pt linkage units out there.

[Hwhipp01 @hwhipp01]

Putting new clutch plates in the slip clutch on the pto. What’s the best way of making sure I have it tight enough. Or is it just keep going till it stops slipping?

[Hwhipp01 @hwhipp01]

Looking for pointers.
Running raven height controller on a 5333 Miller nitro. Have lost connection to controller on gen 4 John Deere monitor.
Haven’t been able to identify any problems many wires and harnesses. Anyone got any ideas based on what lights the controller is showing

[Hwhipp01 @hwhipp01]

@brodenholland Know that feeling all to well. Nothing works when it’s crispy

[Hwhipp01 @hwhipp01]

@AndrewNixon22 That’s all we had. Works well especially being that little bit flexible. Gloves are a must tho, gets a bit on the hot side.

[Hwhipp01 @hwhipp01]

@samheagney @AgrifacAU @nickennis01

[Hwhipp01 @hwhipp01]

@njlawles @MillerSprayers @njlawles John Deere software update seemed to make it work a lot better. Still not amazing but definitely improved it.

[Hwhipp01 @hwhipp01]

Anyone had any luck getting a Miller nitro 5333 steering straight? Running a John Deere 4640 display and a raven industries autotrac controller. @MillerSprayers
@McIntoshDistrib

[Hwhipp01 @hwhipp01]

@nick_bleasdale @lawrencesimps19

[Hwhipp01 @hwhipp01]

@nick_bleasdale @lawrencesimps19 If I remember can get pics on Monday.

[Hwhipp01 @hwhipp01]

@nick_bleasdale @lawrencesimps19

[Hwhipp01 @hwhipp01]

@nick_bleasdale @lawrencesimps19

[Hwhipp01 @hwhipp01]

Has anyone out there fixed the feed drum on a MacDon d65 or 75 to stop it floating and sucking wods of crop thu when direct heading canola or heavy cereals?

[Hwhipp01 @hwhipp01]

Hail storm southern Riverina NSW

[Hwhipp01 @hwhipp01]

Looking around for a tow behind mower conditioner in the central west nsw for dry hire. Old mans mower sideswiped by a car to to causing a write off. Still has contract work lined up.

[Hwhipp01 @hwhipp01]

What toolboxes are everyone using out the for the back of a ute. Wanting to upgrade but want something that's not light weight but also not in the many thousands.

[Hwhipp01 @hwhipp01]

@MerrettContract Think it will be a bit of trial and error with that. The macdon one sits a couple of inches off the back wall and about 3/4 of the way up the wall. But doesn't have any adjustments

[Hwhipp01 @hwhipp01]

Wondering if anyone has put the high speed upgrade in a d65 macdon front to speed up the feed drum? Just wonder which spiker in the gearbox is swapped out for a 26 tooth sprocket and if it has help with feeding issues.