@petermeteor Hopefully yeah!
That SDR was just for testing. Ordered it later than an actual one but it showed up sooner.
And to be clear, that image was from an 80cm offset, not the big 210cm
After years of getting up to this point. It finally happened, Elektro L3 14.5West RDAS received by me, using half purpose-made, half modded equipement.
Aligned by Digitelektro s RDAS align tool, cleaned up in GIMP. At just 5dB avg SNR, there is still a lot of room for improvement
@petermeteor Thanks! I could probably expect like a 3-4dB boost once my new SDR arrives.
For a modded Ku band LNB as the downconverter, it works pretty good
@petermeteor Yeah he only had one chaparral prime feed left, which i got :D
My 210cm dish finally deserves a feed worthy of it anyways. Its been doing L band with suboptimal feeds for way too long.
Finally put my old 120cm dish to use for some Elektro L3 at 14.5West. This dish hasnt seen much active use since getting me some S-VISSR and L3 LRIT (back then at 76East) in 2023
Here are some composites from yesterdays HRIT rx at 12:12UTC
@petermeteor No worries :)
Reminds me of LRIT, but in a good way. Nice work!
Hopefully the new helical works alright! But seeing how you can already get tiny bits of HRIT, you already arent that far from it. The new LNA and maybe some feed adjustments and hopefully you should get it!
@petermeteor LRIT should be doable on as small as a 40cm with an okay setup iam pretty sure. On a 60cm easilly.
You can also get it with a helix directly like Meti wrote about. https://t.co/If4QvC9fZ6
L3 at 14.5W is quite a bit stronger than L5 at 76E so that should make it even easier.
@petermeteor@g5juergenm@aang254@Rommelaar12@Kunstmanen Hi Peter, sorry for taking so long but i just recalled. There is indeed a better pre-made LNA than the sawbird.
Digitelektro (also here on twitter) made. Compact nice sensitive and filtered little things. You could ask him about it maybe. Not sure if he still makes them.
@petermeteor@g5juergenm@menu790@aang254@Rommelaar12@Kunstmanen Honestly there arent that many pre-made options that are as easy to get... A VLNA is like the best there is if you can get the boards for it/build it.
Maybe one of the minicircuit ones would work as well. They do have low noise floor but no filtering so that might cause issues
@ja6_uar Hi, there used to be an old tool called sanchez from nullpainter on github for having underlays on sat imagery. You can try it on L3 RDAS if you want.
@petermeteor@DIYflixit And helix really isnt a good feed option for a prime dish, yet it got it fine. So you should have no problems with your 110 offset and a helix
@petermeteor@DIYflixit Hmm, mby try the focal point or diff turn spacings, (iirc 0.14wl works good?). I get 7dBish on LRIT iirc on 80cm, so you should be easilly able to get HRIT. Even my 80cm should be able to, but not optimised. I got 10dB LRIT and 4dB HRIT on a 120cm prime with 3.5 turn hlx before.
@petermeteor@DIYflixit 7.5 turns really seems like a lot for a usual offset dish. You might be underilluminating it. What is your SNR? I can compare it to my (not super optimised just yet) 80cm dish also getting L3
(Also for SNR, prolly do some other slot than 12:42, as thatone exleriences sun noise.
@CarlosMartinsl3@ja6_uar Hi, LRIT from both 76East and 14.5West are receivable anywhere in the sat footprint. Try checking ggak and aiming by that. Do that when Elektro L2 is at 0lat, GGAK still comes from L2. Or you can use the xRIT carrier. This is considering you are using the typical LRIT/HRPT setup.