6tanks

[6tanks @6tanks1]

@MKD_D27 Thanks for asking, but I'm not planning to sell the files any time soon.

[6tanks @6tanks1]

I made a 3D printed replica of the BKM-140M; the 16:9 widescreen mask for the PVM-14L5. Spend a lot of time getting the fit & surface texture to match the original. They're available here if anyone is interested:

https://t.co/kcA3uv5w4N

[6tanks @6tanks1]

@redbumboo @mattysaurus Compare the diagram in the user manual with the one on eBay to make sure it has the correct buttons

[6tanks @6tanks1]

@redbumboo @mattysaurus I have found a couple. It's made by Funai so some Emerson and Sylvania DVD combo remotes will work. Can't remember the model numbers.

[6tanks @6tanks1]

I designed this replacement Sony badge for the PVM-2030 & 2530. Took a lot of prototypes, but it fits just like the original and has a nice glossy surface finish. Working on some for other PVM models that should be ready soon.

They're available here:
https://t.co/egmdpHIdQG

[6tanks @6tanks1]

@jormungandrizer @KytorIndustries I totally could, but I'd need a huge print bed to actually produce it. One of these days!

[6tanks @6tanks1]

@Stack3rr My usual strategy for case damage is to either print custom patches or cut pieces from ABS sheet. Then you can glue them in with ABS pipe cement.

[6tanks @6tanks1]

@Stack3rr My printer isn't quite big enough for that. What's the problem with yours? Sometimes you can print small patch sections - it works best with ABS since you can glue it to the original case.

[6tanks @6tanks1]

@BlueShell3D Thank you!

[6tanks @6tanks1]

Also fits the international variants - PVM-14L3, PVM14L4, and PVM-D14L5A.

[6tanks @6tanks1]

@usa_retro Sometimes it works! But often it doesn't.

[6tanks @6tanks1]

@usa_retro Hey, that Pelco is really good. Those PC monitor tubes are crazy sharp! RGB mod it and it becomes a 700 TVL PVM.

[6tanks @6tanks1]

This was inspired by the GC Electronics 8606-L, the GOAT of alignment tools which appears to be OOP and hard to find. The printed version seems to work just as well.

[6tanks @6tanks1]

Finished my design for 3D printed CRT alignment tools. The long handled one is great for those width coils & pots that are stuck waaay down in the middle of the TV.

https://t.co/3r72KoyYKn

[6tanks @6tanks1]

Had an idea for some 3D printed CRT alignment tools today. So far they're working very well! Still have a ways to go on the design.

[6tanks @6tanks1]

I made this 3D printed replacement for the Minolta CA-100 probe holster. Very useful if yours is missing.

https://t.co/K6rezFb9tF

[6tanks @6tanks1]

@hitmanmcc Sure, if you need one just send me a DM and I can print you some.

[6tanks @6tanks1]

Finished another 3D print project. This time, I designed a replacement front bezel for the JVC TM-A101G. Very happy with it! It took a while to figure out how to model the button panel in a was that was functional and could print well.

[6tanks @6tanks1]

@TO I took the original bezel, measured it with calipers, and tried to recreate it in a form that could be printed cleanly.

[6tanks @6tanks1]

@BlueShell3D Mostly it's because I'm making prototypes from random colored filaments!

[6tanks @6tanks1]

@mista_b_man I've experimented with 3D printed decals (here's one I made for a TM-1051DG). They work well but the resolution isn't quite as good as I'd like.

[6tanks @6tanks1]

@mista_b_man That's the original front panel sticker. It's easy to peel it off and reapply.

I'd like to make reproduction stickers, but haven't found a place to print them yet.