Andrew Cadd

[Andrew Cadd @AndrewCadd3]

@PrimarySales @BushelPlus I’ll buy 10 if it gets me a 10 T/ha increase in yield 😳

[Andrew Cadd @AndrewCadd3]

@Adamsherry58854 @DraffinChris @JacintaAllanMP done that 10 yrs ago regarding sector reform here in Sa, 50 fire trucks on steps of Parliament House, we were more civil about it, got results

[Andrew Cadd @AndrewCadd3]

@hasselljpb Get one of these, much safer
https://t.co/guzemow1t6

[Andrew Cadd @AndrewCadd3]

@CurnowGreg 🤣🤣🤣

[Andrew Cadd @AndrewCadd3]

@farmersgrowit @IamFarmerRenee Especially when the older farmers didn’t have chemical filters for the cab, if they had a cab

[Andrew Cadd @AndrewCadd3]

@CorbinSchuster We should ask our farming industry body reps to raise this issue. For me as a farmer the Buckland park radar has never been much use since it’s major upgrade a few years ago. Would a radar on EP help SA?

[Andrew Cadd @AndrewCadd3]

@AdamCoffeyNT Guess it was gel form ? gel concerns me

[Andrew Cadd @AndrewCadd3]

Excellent lunch at the Magpie & Stump hotel, Mintaro

[Andrew Cadd @AndrewCadd3]

@percytonfarmer @australiapost Check all the freight depots in case it’s at one

[Andrew Cadd @AndrewCadd3]

@farmersgrowit @Telstra @GrainProducerSA Yep when we loose 3G we’ll see how bad 4g is for coverage

[Andrew Cadd @AndrewCadd3]

@Thomas85158396 I hear you Thomas, radial tyres 🙄 I don’t think we would ever wear them out before they crack, so wasteful

[Andrew Cadd @AndrewCadd3]

@GBubner @BlacketPeter 🤣🤣🤣

[Andrew Cadd @AndrewCadd3]

Grease too hard when cold? Tub of water & fish tank heater on max overnight fixes it

[Andrew Cadd @AndrewCadd3]

@HoolyMcg That happens all the time here in SA, radar says it’s raining=clear sky, radar says it’s clear=rain 😡

[Andrew Cadd @AndrewCadd3]

@CropDoctor54 @WeedSmartAU @FMCANZ @theGRDC @GRDCSouth @AHRI_Team Is on coarse registered for our use?

[Andrew Cadd @AndrewCadd3]

@paulD74465326 @FMCANZ

[Andrew Cadd @AndrewCadd3]

@CropDoctor54 Approval & support from the header manufacturer eg warranty if fitting to new header

[Andrew Cadd @AndrewCadd3]

@IanCocko 4, almost forgot, lastly balance. Bearing at each end without seals or grease, just lube with wd40 or thinner. Weld balance weights on back of flight about 3cm or so in from outer edge

[Andrew Cadd @AndrewCadd3]

@IanCocko 3, cut off the puller legs and clean up. Hope my diagram makes sense.

[Andrew Cadd @AndrewCadd3]

@IanCocko 2, Turn the threaded centre bolt on the puller, the flight will pull up until very little or no gap is left. Then weld that end to the centre tube. You will have excess flight, cut it off after welding. Weld the rest to centre tube but have a weld sequence as not to warp the tube