GoBigCAD is a product design and mechanical engineering studio.
We help hardware founders, manufacturers and engineering teams go from concept to manufacturing-ready CAD, with DFM built in.
Follow for renders, mechanisms and practical DFM tips.
https://t.co/rb848fE8P7
@wenxinc0612@AttentionAGI Been there. What usually unsticks the enclosure is freezing the PCB outline, connector positions and tallest parts first, then designing the housing around that envelope with draft and wall thickness for moulding from day one. Rev 6 boards keep moving the target otherwise.
@Fiercel1on@Kicksbuttson Agreed, heat-set inserts make a big difference for anything that gets reassembled. Leave enough wall around the boss so it doesn't crack on install, and a small lead-in chamfer helps the insert go in straight.
Draft is the slight taper that lets a moulded part leave the tool. Here is the longer walkthrough of why it matters, and where it goes on the part.
#DFM#InjectionMolding#Engineering
@Kicksbuttson Epoxy works if you never need to open it again. For next time, brass heat-set inserts pressed in with a soldering iron hold screws much better than printed threads, and the case can be opened as often as you like. Leave 2 to 3 walls around each insert so the boss doesn't split.
@MatthiasWagner@sibinarendran@BuildWithFlux Doing both in one place would help a lot. The handoff between the board and the case is where most fit problems start. Curious how it deals with real-world tolerances and print shrink.
Measure the board, battery and screen (calipers or datasheets), model them as simple blocks in Onshape or Tinkercad, then draw a box around them with ~2 mm walls and ~0.3 mm clearance. Print it fast and test the fit. If you'd rather hand off the case design, happy to help, just DM us.
@MinimalCompany PCB revision → DVT assembly is the milestone that usually surfaces housing stack-up issues. Worth confirming connector protrusion, battery clearance and screw-boss crush before locking the next enclosure cut.
@MattiaFiumara In-house SMT + assembly is the real unlock for weekly hardware drops — the design loop only stays that fast if DFM and tooling live next to the CAD team. Most startups lose a week every time a revision leaves the building.
@ethanbutwoke@OSHCutInc OSHCut + COTS is a strong constraint set for AI-generated sheet metal — bend radii, hole-to-edge, and gauge choice usually decide whether the first cut ships or comes back. Curious how the model handles flat patterns vs formed assemblies when the material callouts change.
@mikejt4 The 'CAD package without a render window' line lands. A lot of mechanical work is exactly that — a spatial model you can spin and constrain, not a mental photograph. Curious whether having the model on screen changes how you design, or if the internal spin is already enough.
Agree that manufacturing readiness stays a human loop. The handoff that still breaks prototypes is mech↔elec: keep-outs, connector stack height, and fastener bosses that fight the PCB outline. Agents can draft both sides; someone still has to check the assembly for interference before the first CM quote.
Suppressing the rebend and working from the flat config is the right move for that slot pattern. Unbend → cut → rebend forces a full flat-pattern rebuild every regen; a flat-first config with rebend suppressed (or a derived config for drawings) usually drops that wait from minutes to seconds. The Frustration Fee feels earned.
Respect for designing three versions with stiffness and torque as the drivers, not cosmetics. The epoxy bed pour + tram blocks for coplanar rails/headstock is a clever shop-friendly fix. On the spindle enclosure (you mentioned capping rpm until it has one): leave service access for the belt/pulleys and keep the chip path clear of the guard — those two details decide whether the enclosure helps or fights you.
Solo hardware is hard — nice to see the first enclosure off the printer. The part that usually bites next is fit around the board: connector clearance, venting for heat, and how the lid/base stack without crushing buttons or flexing the PCB. Worth a dry-fit pass with the real electronics before the next CAD spin.
Coupon printing for PCB mounts and screw posts is a smart way to burn less PLA while you learn. One thing that bites when you leave the printer for production: draft, even wall thickness, and boss sizes that survive a material change (PLA → ABS/PC or a moulded resin). Worth running that checklist once the BOM settles, before you freeze the grille and overall form.
SLA is great for stiff Microduck bodies; the squishy feet want a different process. TPU prints work for a first pass if you keep walls thick enough to bond, but a silicone overmold (or a printed TPU insert that press-fits into the SLA ankle) usually feels more like a foot and survives the waddle. Worth picking a Shore hardness before you reprint the legs around it.
Keeping the factory enclosure and printing only the backplate is the right trade — you keep the button, fan, and LoRaWAN fit. The details that decide whether that plate helps or fights you: USB port alignment and edge clearance, strain relief so cables don't lever the print, and not blocking the fan path. A couple of locating pins into the original case usually beat relying on friction alone.
Point 15 is the one that sinks a lot of first gadgets: a sealed printed box will cook Li-ion and reset boards. A few vents (or a metal plate the hot parts can sink into) plus leaving the pack off interior walls usually does more than another firmware pass. Same pass is a good time to check boss and rib layout if that box might later become a moulded part.
That printed-case durability lesson is the one most first hardware projects learn the expensive way. Changing the internal structure after the 3D-printed cases flexed, and modifying the Type-C strain area so it actually fits, is real DFM — not a failure. Connector keep-out, wall thickness, and how loads go into the housing usually decide whether proto 3 survives being plugged in every day.