Michael Delaney

“drone kid”

[Michael Delaney @MichaelD_33]

After over two years of work, my custom built quadcopter takes flight! Hear all about the project: https://t.co/axjIIVCSW3

[Michael Delaney @MichaelD_33]

@printrbot This is awesome! Printrbot has been gone for far too long. My support goes out to the PB family. Super excited to hear you’re back. I will definitely be getting some 2020 swag!

[Michael Delaney @MichaelD_33]

A few photos of the drone project I’ve been working on, recently. There’s a lot to talk about with this project. Expect more info soon.

[UltiMaker @Ultimaker]

#ICYMI - While creating a programmable #quadcopter, Michael Delaney (@MichaelD_33), a student at Avenues in NYC, went through various iterations and changes. Read about the relatable iterative process in this blog post: https://t.co/3txfmfKMnC

[Michael Delaney @MichaelD_33]

Check out the blog post I wrote for @Ultimaker on tools of the design process and their influence in designing my #AIOQuadcopter flight controller! https://t.co/FcePUrEwfQ

[Michael Delaney @MichaelD_33]

Assembled version of my all-in-one quadcopter circuit board. Still making a few changes to the design, but everything functions properly. #electronics #circuitboard #pcbdesign #quadcopter

[Michael Delaney @MichaelD_33]

Working on a new PCB design. Can anyone guess what it may be?? #pcbdesign #electronics

[Michael Delaney @MichaelD_33]

Lots O’ PCBs! and SMD soldering... #electronics #pcbdesign

[Michael Delaney @MichaelD_33]

Check out my project on @hackadayio for a breakdown and comprehensive overview of the process behind the design of my homemade FPV monitor! It's got a lot of great information about the design and doing DIY PCB etching at home. Let me know what you think! https://t.co/OrURgy0FrF

[Michael Delaney @MichaelD_33]

Making some upgrades to my custom built FPV monitor. The new version supports a detachable SMA antenna, embedded arduino, built-in 1S lipo and charger, and a 12v boost circuit. Still cost 2-3x less than the average commercial monitor. Files will be available on github soon.

[Michael Delaney @MichaelD_33]

I figured it was about time I build one of these.... #nixietubeclock #electronics #lasercut

[Michael Delaney @MichaelD_33]

Some PCB etching for an experimental project I am working on in Shenzhen, made using only Vinegar, Hydrogen Peroxide and Salt. Board is coated in UV soldermask for easy PCB layout transfer, 3 minutes in the sun and the layout was transferred. Super cool!

[Michael Delaney @MichaelD_33]

Back from my trip! I spent 2 weeks this summer traveling to Tanzania to Climb Mt. Kilimanjaro! After 19,340 so feet...

[Michael Delaney @MichaelD_33]

@printrbot where you at? 😀

[Michael Delaney @MichaelD_33]

Part 1 complete

[Michael Delaney @MichaelD_33]

Carbon fiber resin infusion!

[Michael Delaney @MichaelD_33]

Received some water jet cut Motor mounts for the electric skateboard!! Excited!

[Michael Delaney @MichaelD_33]

Ok, everything should work, but when I go to use my rf receiver. It's receiving the signal, but the ESC just doesn't work.

[Michael Delaney @MichaelD_33]

Got some skateboard parts in the mail today... Super excited!

[Michael Delaney @MichaelD_33]

Prototype electric skateboard!! Super fun!