Hard to believe it's been 10 years since my first team event triathlon. The runner was an accomplished sub-3hr marathoner, the biker a lifelong triathlete and accomplished rider and then there was me... I had only just taught myself to open water swim earlier in 2015!
We all agreed on the team name Sandpit Snails, "sandpit" for city built in the desert and "snails" because we would be slow, but primarily because of their swimmer, yours truly😂
Naturally there were huge swells that morning and I ended up having to breast stroke for half of the swim, but I finished and that's all that matters!
Slow and steady finishes the race, whether a triathlon, longterm investing or life in general... keep taking meaningful steps forward and don't forget to enjoy the journey along the way.
Agreed, it needs to be addressed.
Availing of a rule that ultimately casts shade on the sport, a rule that opens the door for players to have a bad experience through no fault of their own, is a rule that needs to be changed.
This should have been a “red card” but is technically permitted under the rules.
@booster_10 First thing that came to mind was starting fires with a 9 volt battery and fine steel wool!
Clearly that’s not the kind of steel wool he meant 😅
Joe to the rescue:
https://t.co/82u02rNkZG
For future Starships, some people have asked about the ablative layers in the sides of the ships and how they can be able to survive the catches while providing protection and not being damaged.
@elonmusk has stated the ablative sheets will be replaced by a stainless steel wool material. Here’s how it works and its @NASA history.
Stainless steel wool can serve as a durable, reusable fibrous insulation layer that provides thermal protection on lower-heat areas (like the sides) while being mechanically robust enough to survive contact with the chopsticks during catch.
For the sides and leeward areas of Starship, these areas experience significantly lower heating and the stainless-steel hull itself already has a high temperature tolerance (useful structural strength well into the hundreds of °C, melting point ~1400 °C), and secondary layers provide extra margin.
Stainless steel wool works as insulation the same way other fibrous materials do (ceramic fiber blankets, mineral wool, etc.):
• The fine metal filaments trap gas (air or the low-pressure atmosphere during reentry) in a large void volume
• This creates low effective thermal conductivity via the gas and the long, tortuous heat-conduction paths through the fibers
• Densities in historical metal-wool concepts were in the roughly 60–85 kg/m³ range, competitive with other high-performance insulations
A 1974 NASA study specifically evaluated metal-wool packaging for reusable heat shields on Shuttle-like vehicles.
It concluded that metal wool is thermally competitive with the best insulations, has low weight, resists chemical attack, and is practical with 300-series stainless steel up to ~1250 K (~977 °C / 1790 °F) under appropriate load and oxygen conditions, with structural stainless sheet accommodating even higher temperatures (~1360 K) for expansion management.
Because the material is non-ablative (it does not intentionally erode or char away), it stays in place across multiple flights rather than requiring full replacement after each reentry, aligning with Starship’s rapid-reuse goals.
On the sides, where peak temperatures are moderated, this level of insulation plus the underlying steel is expected to be sufficient.
The current ablative sheets/layers (and related felt materials) are relatively soft and get mechanically scraped or abraded where the catch arms contact the vehicle. Stainless steel wool is metallic and far tougher:
• It is inherently impact- and abrasion-resistant (explicitly noted as an advantage in the NASA metal-wool work)
• It can compress and flex under the load of the arms without being sheared off or destroyed the way soft ablative or felt layers are
• It is the same material family as the ship’s structure, so thermal-expansion compatibility and attachment are straightforward
In short, the wool trades the “sacrificial” thermal behavior of ablatives for a durable, porous metallic insulator that still limits heat transfer to the structure while surviving the mechanical demands of tower catch.
Image of current ablative material damage on Ship 42 by @NASASpaceflight@esherifftv
Considering most people are hard pressed to get even 10-15 strict pull-ups, I’d say it’s a moot point. If you mechanically can’t do one more pull-up, mission accomplished, hypertrophy achieved.
If you’re among the few that can rep 20 or more, then weighted may be the better option.
@DavidLe76335983 Realistic / Optimus (Radio Shack) - maybe not in the same league as Sony, Onkyo and others, but it was hard to beat a pair of Mach 3 speakers.
What I do is log into remote console and update the firewall. On a VPS, this would be via the web console (e.g. Hostinger), else remote KVM (iDRAC, ILO, etc).
But if you only have your phone, remote console access may not be feasible.
So alternatively, install Hermes, setup Telegram gateway (or other), designate a user with only sudo privileges to add an IP to the firewall and simply message Hermes Agent to add <new IP> to the firewall via that privileged user.
I use both methods.
Granted, many prefer the ease of just using Tailscale, but I’m not comfortable giving a corporation access to my kit.
Besides, corporations have to follow country rules and that typically means they are already pwned by their government agencies. 🤷♂️