Peter Wallhead

Embedded systems developer, hardware hacker and tech industry enthusiast.

[Peter Wallhead @peterwallhead]

You know it's bad when @uptimerobot starts going offline... It's been glitching for about a week. What did you break, folks?

[Peter Wallhead @peterwallhead]

So @SkycardsHQ #skycards is down, @flightradar24? Not loading past the loading screen anymore. Tried the app update, didn't help.

[Peter Wallhead @peterwallhead]

Remember when we use to close all the Google tabs when you finally solved a coding problem? Now we close ChatGPT tabs...

[Peter Wallhead @peterwallhead]

Well, it's trying to drive in a straight line, but it's not quite there yet 😅 #ros2 #rviz2 #robotics #slam

[Peter Wallhead @peterwallhead]

It's been a minute or 2, but check out the first custom PCB I've designed for my SLAMBOT project. PCB printing sponsored by @PCBWayOfficial

[Peter Wallhead @peterwallhead]

I also have 3-5 of your older mugs, but none of those seem to be fading, yet. This mug was ordered on March 28, 2024, but I've only just started to dishwash it.

[Peter Wallhead @peterwallhead]

@Printful I was under the impression that your mugs were dishwasher safe? If so, why is the ink fading after only 5 washers? Produced by your Aus supplier, if it helps.

[Peter Wallhead @peterwallhead]

@fireflyspace Did you guys forget to rotate the picture 90 degrees to the left?

[Peter Wallhead @peterwallhead]

Excuse the low resolution, but my #SLAM edge detection algorithm is coming along nicely (the grey and blue dots) overlayed on 2 different scans. The trick will be to ensure I have enough of the same edges detected in multiple scans to compare for pose estimation.

[Peter Wallhead @peterwallhead]

I wish @CommBank, or any bank for that matter, had conditional automated transactions. Eg. If at the end of the month I have x dollars in an account then transfer y dollars to savings. Smart Savings is close to what I need, but not quite there.

[Peter Wallhead @peterwallhead]

@lukas_m_ziegler In case anyone else needs the source link like I did: https://t.co/1tnZfbCHts

[Peter Wallhead @peterwallhead]

@boxcardavid @Willrandship ChatGPT concours. Google "louvered panel system"

[Peter Wallhead @peterwallhead]

@JLC3DP @JLCPCB https://t.co/Hce0qM0kSk if you want to follow along more.

[Peter Wallhead @peterwallhead]

Hey @JLC3DP/@JLCPCB want to sponsor my next awesome robot build so I can demonstrate your large scale printing abilities?

[Peter Wallhead @peterwallhead]

@jimbelosic *cough* Come to Australia *cough*

[Peter Wallhead @peterwallhead]

Another day, another flying attempt. One good flight in, one undercarriage mount folding incident that needed a couple of cable ties to fix, and its nose fell off. No broken props though!

[Peter Wallhead @peterwallhead]

@webronen Thanks! Eventually it will become the surrounding shell for this little guy. Definitely not a secret, but very early in the project still :)

[Peter Wallhead @peterwallhead]

I'm loving @autodesk Fusion 360 (Personal) so far! @openscad was great as a beginner, but Fusion is taking it to the next level.

[Peter Wallhead @peterwallhead]

Sometimes in life you'll make a mistake, and that's ok. Just make sure you always keep a couple of shims handy.

[Peter Wallhead @peterwallhead]

@jimbelosic @sendcutsend We must be getting close to an Aus launch date now? :)

[Peter Wallhead @peterwallhead]

@jimbelosic when might you be branching out @sendcutsend onto Australian shores please? We desperately need you down here, and I get so jealous when I see US Youtubers using your fantastic service.