John Hashmore 🟧💨🔥

[John Hashmore 🟧💨🔥 @MountHashmore]

@CJHandmer After two harness replacements I finally pulled my wire harness and wrapped it with two layers of Kevlar twill fabric, then wrapped the whole thing in Honda hot pepper oil infused electrical tape. Also got two outdoor cats. No problems since.

[John Hashmore 🟧💨🔥 @MountHashmore]

@HEN3DRIK What’s your workflow? Vibe-pcb design is going to unlock a lot of capabilities for me.

[John Hashmore 🟧💨🔥 @MountHashmore]

@peterktodd Yikes dude

[John Hashmore 🟧💨🔥 @MountHashmore]

@LPCapitalChi I hate mine, go with seed signer.

[John Hashmore 🟧💨🔥 @MountHashmore]

@KrisAltairtech I did this mod, but the main voltage busses won’t power up. It powers the control board, and fans turn on, but no bus voltage.

[John Hashmore 🟧💨🔥 @MountHashmore]

@tether @grok are any founders of tether connected to the Epstein files?

[John Hashmore 🟧💨🔥 @MountHashmore]

@Braiins

[John Hashmore 🟧💨🔥 @MountHashmore]

@tylerkstevens @alphazeta It turns all of the energy into heat, change my mind.

[John Hashmore 🟧💨🔥 @MountHashmore]

@mrmasternode Sure do, do you have an s12 fan?

[John Hashmore 🟧💨🔥 @MountHashmore]

Are you minimizing the wife approval factor with your builds anon? Are you throwing aesthetics to the wind in pursuit of performance? If not, you’re NGMI.

[John Hashmore 🟧💨🔥 @MountHashmore]

@tylerkstevens @256FOUNDATION Is that a functioning libre board in real life? I cannot wait to get my hands on one of these. Or a dozen.

[John Hashmore 🟧💨🔥 @MountHashmore]

Haven’t had time to work on the Universal Miner Thermostat, but it’s been working for me keeping my garage at 60 degrees for weeks now. I’ve had to restart a hashboard twice, but other than that it’s been rock solid!

[John Hashmore 🟧💨🔥 @MountHashmore]

@tylerkstevens @256FOUNDATION Are those the intel chips?

[John Hashmore 🟧💨🔥 @MountHashmore]

@mrmasternode @CincoDoggos I just tap into the PWM wire in the fan, it’s in the square protrusion on the side of the fan. Easy control with arduino/esp32/pi

[John Hashmore 🟧💨🔥 @MountHashmore]

@MolonLabeVC Good question, this is optimized for two things: 1. Universality and 2. Bedrooms. I run my fans constant speed all the time (they’re very quiet) so that there is no sound change during operation. This is critical for not disrupting sleep. Curtail = simple and always works.

[John Hashmore 🟧💨🔥 @MountHashmore]

Getting close to a functioning, universal miner thermostat. No Home Assistant needed.

1. Plug device into Ethernet
2. Set IP of miner (miner must use luxOS firmware)
3. Set goal temp

That’s it! Your miner will toggle curtail on and off to maintain the goal temp in the room. Running fans at constant speed makes the miner hardly noticeable, even in bedrooms. Likely cannot get any easier to start heating with bitcoin miners.

[John Hashmore 🟧💨🔥 @MountHashmore]

@Printer_Gobrrr Does this run S19 hashboards! What is this wizardry??

[John Hashmore 🟧💨🔥 @MountHashmore]

@MolonLabeVC @SatStackingPleb @Silexperience @mrmasternode @luxor Watts per dollar is untouchable with apw3’s

[John Hashmore 🟧💨🔥 @MountHashmore]

@SatStackingPleb @MolonLabeVC @Silexperience @mrmasternode @luxor This is true. @synthex21 to the rescue!

[John Hashmore 🟧💨🔥 @MountHashmore]

@SatStackingPleb @MolonLabeVC @Silexperience @mrmasternode I asked @luxor for this in person at last years heat punk summit and the answer I got was that development for heating applications is not very high on their priority list. Maybe things are different now.

[John Hashmore 🟧💨🔥 @MountHashmore]

@SatStackingPleb @MolonLabeVC @Silexperience @mrmasternode 1. Auto recognize any PSU as apw12
2. Allow unused 4th hashboard port to still bring in temperature over i2c for room temp
3. Add thermostat functionality