j/p

[j/p @jpc0mps]

@skot9000 @francispouliot_ Check out @zoodotdev

[j/p @jpc0mps]

@SatStackingPleb @guzmanpintos @skot9000 did we end up merging that into ESP-Miner?

[j/p @jpc0mps]

@guzmanpintos @SatStackingPleb ^ this is the answer. The threshold voltage of the transistors shift as temp changes. Keep in mind, temps on most Bitmain FW/Boards is an est of the die temps as they use a lm75 on the board + offset. If you really want to see take a look at a BM1368(S21) which has on-die temps

[j/p @jpc0mps]

@SatStackingPleb @altair_tech @ePICBlockchain Can't wait for you to try, let me know if you have any questions

[j/p @jpc0mps]

@skot9000 @kevinaltairtech @denverbitcoin @CryptoMinerCHR @ndgo1370 @zbomstaz I know @guzmanpintos and LuxOS has previewed the amount of data/samples required to build an accurate model
https://t.co/yrXFVF56N4

The APW17 introducing accurate power reading over the PSU protocol was a welcome addition

[Guzman Pintos @guzmanpintos]

Working on improving LuxOS power estimator.

[j/p @jpc0mps]

@skot9000 @kevinaltairtech @denverbitcoin @CryptoMinerCHR @ndgo1370 @zbomstaz You can go all the way down the rabbit hole here..but to keep it simple. APW12 doesn't have any current reading capabilities exposed so when we do power estimation in ePIC FW (and most other FWs) we do a power estimation based around 3 variables (Voltage, Freq and Temp)

[j/p @jpc0mps]

@SatStackingPleb @denverbitcoin @CryoByteLabs @braiins @luxor very doable. you'll prob be touching ~1000W but that should be ok at 120V

[j/p @jpc0mps]

@keegreil @SatStackingPleb @ePICBlockchain @altair_tech @zbomstaz I like @SatStackingPleb idea of enabling you to set the bounds, unfortunately without control of the PSU won't do much, but will help with the tuning algos internally and speed them up for sure

[j/p @jpc0mps]

@keegreil @SatStackingPleb @ePICBlockchain @altair_tech @zbomstaz We wanted to be on the safer side and make sure that the setting wasn't accidentally enabled for miners running at scale in a normal environment, but this is a good time to revisit this.

[j/p @jpc0mps]

@SatStackingPleb @keegreil @ePICBlockchain @altair_tech Noctuas, if I recall they have a fan splitter in the box, that would prob be my recommendation as it already removes the sense on the second fan.

[j/p @jpc0mps]

@SatStackingPleb @keegreil @ePICBlockchain @altair_tech you can, just need to be a bit careful. The fan headers are in parallel of each other so if you do want to use the connector you'll want to make sure the SENSE line is disconnected on one of them (FAN1 MOLEX -- FAN1 4pin).

[j/p @jpc0mps]

@skot9000 @keegreil As you suspected I expect it to most likely the DHCP discover and some network init. If you see anything else and have any questions just ping me

[j/p @jpc0mps]

@keegreil no dev-fee, no phoning home. give the UMC a try. API fully documented and open. Also welcome the packet audit! If theres something that shouldn't be there that we missed will address it.

[j/p @jpc0mps]

@zherbert Congrats!!

[Perry Hothi @perryhtee]

Here’s what we’ve been up to
3nm ✅
15 Exahashes ✅
One of the largest Hashrate agreements✅
New upgradable platform ✅

Boom!!
@blocks @Core_Scientific @ePICBlockchain

https://t.co/uExdE6uTFF

[j/p @jpc0mps]

@OGBTC @marcfresa @perryhtee

[j/p @jpc0mps]

@OGBTC @marcfresa @perryhtee Don’t worry I’ll like your post too, just not the one that is factually incorrect. Happy to talk chip design with you anytime as always

[ePIC Blockchain @ePICBlockchain]

🚀 ePIC CTO, Earl Mai, joined @wsfoxley on @theMiningPod at #Consensus2024 to discuss “The Future of Mining Hardware” For those who missed it, the official podcast is now available! 🎧

Watch now: https://t.co/tral7cJ9Pk

#BTCMining #ePICBlockchain #FutureOfMining

[j/p @jpc0mps]

@skot9000 @altair_tech @0x0B17C019 @SatStackingPleb yup, so you just need i2c, 3.3V and GND. here is the code that matched the video. in no way production ready...

https://t.co/JpXuLdArZS