@SantiagosStacks Point 3 catches a lot of people out. Where mass can't tell you, the chromatogram sometimes can: mispaired isomers often show up as a shoulder or a small peak near the main one. One clean peak at the right mass is far more reassuring.
What does it cost to check a vial in the UK?
Purity only (HPLC): from £129
Purity + identity (HPLC + LC-MS): £300 each for your first 5 samples, then £349
We aim for ~7 working days
BPC-157 · GHK-Cu
https://t.co/2GnzVUviW7
RUO only
@jamiegagnon@agingroy Small correction on the chemistry: GHK-Cu is one tripeptide (glycine, histidine, lysine) holding a copper ion, not three chains. And "tested when you buy" only means something if the CoA shows both purity and identity for that exact lot.
What happens to a sample once it reaches the lab:
Logged against its lot number
Weighed and dissolved
Run on HPLC for purity
Run on LC-MS for identity
Reported as a measured number
We aim for ~7 working days.
BPC-157 · GHK-Cu
https://t.co/2GnzVUviW7
RUO only
Before trusting a CoA, try three things:
Look the report up on the lab's own site, not the seller's copy.
Check there's a chromatogram, not just a %.
See whether expected and measured mass are both shown.
Testing BPC-157 · GHK-Cu
https://t.co/2GnzVUviW7
RUO only
@Natertottzz Worth adding that a sterility pass and a low endotoxin result are only as good as the sample that was tested, so the lot number needs to match there too. Purity, identity and sterility are three separate questions.
@TrustPointe Sequence scrambles are the classic trap there. Same mass, different order, and only an orthogonal check catches it. Do you find co-injection with the reference standard settles most of those cases, or do you end up going to MS/MS fragments?
A purity number tells you a sample is clean.
It doesn't tell you what it is.
That's identity: LC-MS checks the measured mass against the peptide on the label.
Clean and confirmed is the pair worth asking for.
Testing BPC-157 · GHK-Cu
https://t.co/2GnzVUvQLF
RUO only #HPLC
HPLC shows how clean a sample is. LC-MS shows it's the right peptide.
UK prices per sample:
Purity (HPLC) from £129
HPLC + LC-MS £300 for your first 5, then £349
We aim for ~7 working days
BPC-157 · GHK-Cu
https://t.co/2GnzVUviW7
RUO only #PeptideTesting
@PeptideBriefs That line deserves a pin. Peer review beats peer pressure when you're staring at a CoA. We publish how we read purity and identity at https://t.co/2GnzVUvQLF — RUO only.
@labratdlux On the identity side we use LC-MS and match the measured mass to the named sequence. Happy to dig into analyser class another time if useful.
Reading a chromatogram:
The tall main peak is the peptide. Small peaks are impurities.
Purity % is main peak area over total area.
What it can't show is which peptide it is. That needs LC-MS.
Testing BPC-157 · GHK-Cu
https://t.co/2GnzVUvQLF
RUO only #HPLC
@peptigrity Checking the search code on the lab's own portal is the bit most people skip. A PDF on a shop site is easy to edit; the lab's record isn't.
@troywhiteyyc@pepfessions That lineup is exactly what people need. The quiet failures usually sit in the gap between a tidy purity % and a mass that doesn't match the label.
How a peptide test works:
1. HPLC separates the main peak from impurities → purity %
2. LC-MS checks the mass matches the named peptide
Without both, the CoA is incomplete.
BPC-157 · GHK-Cu
https://t.co/2GnzVUviW7
RUO only #HPLC
Three quick CoA checks:
Does the lot number match your vial's label?
Is the test date plausible for that batch?
Is the measured mass close to the peptide's expected mass?
A no to any is worth asking about.
Testing BPC-157 · GHK-Cu
https://t.co/2GnzVUviW7
RUO only #CoA
@Vanguard_Lab@mycenaskin Peptide content tells you how much is there, area % tells you how clean the main peak is, and neither says it's the right sequence. We've seen people stop at the content number and forget to ask for a mass match on the same lot.
Purity asks: how much of what's in the vial is the main compound?
Identity asks: is that compound the peptide on the label?
A 99% result on the wrong sequence is still the wrong peptide, so a CoA needs both.
Testing BPC-157 · GHK-Cu
https://t.co/2GnzVUvQLF
RUO only #LCMS
@AbudBakri Hard part isn't the machine, it's the paperwork around it. A purity % with no chromatogram and no identity check tells you very little. If a lab shows the raw trace and a mass match tied to your lot number, most of the argument goes away.
Testing a peptide in the UK, what it costs:
£300 a sample for HPLC + LC-MS (purity and identity on one CoA) for your first 5, then £349
Need purity only? HPLC from £129
We aim for ~7 working days
BPC-157 · GHK-Cu
https://t.co/2GnzVUviW7
RUO only #PeptideTesting